SearchFAQMemberlist Log in
Reply to topic Page 1 of 1
Near line volume?
Author Message
Post Near line volume? 
What exactly is a near line volume?

If add '-q near' to mminfo command what will it do differently?

Thanks.

George

Note: To sign off this list, send a "signoff networker" command via email
should be sent to stan < at > temple.edu

Post Near line volume? 
What exactly is a near line volume?

A volume that is in an addressible jukebox. It may not be mounted at
the moment, but it can be mounted without operator intervention. An
offline volume is not in a jukebox, and cannot be mounted by Networker.

If add '-q near' to mminfo command what will it do differently?

It will only show nearline (jukebox) volumes.

Darren Dunham ddunham < at > taos.com
Senior Technical Consultant TAOS http://www.taos.com/
Got some Dr Pepper? San Francisco, CA bay area
< This line left intentionally blank to confuse you. >

Note: To sign off this list, send a "signoff networker" command via email
should be sent to stan < at > temple.edu

Post  
Hello,

I have a question about nearline volumes.

We eject all our full tapes from library and also remove them from CAP. So the tapes are not there physicaly. We have a script which is updating locations, but first it finds out whether or not we have tape in a library (via -q near). If the tape is in library, but the location differs, it prints out an error message.

The problem is we are still getting these error messages, because when i run
"mminfo -q near -xc, -r volume " I still have these volumes on the list even if they are not physicaluy in the library... Our offsite storage guys confirmed, that tapes arrived and are there. So its no way we can have them in library.

Any ideas why is this? How is it possible? And how can I convince our library to show only the tapes that are really there? how mminfo determines whether the tape is in library or not?

View user's profile Send private message
Post Near line volume? 
Are you using nsrjb or NMC to withdraw the tapes? Or, are you using a
non-NetWorker command?

I would suggest using sjirdtag to verify the contents of the library instead
of mminfo, if possible. There are a few scenarios where mminfo isn't
properly updated, while sjirdtag is almost always correct.


On Mon, May 17, 2010 at 4:56 AM, kurtica
<networker-forum < at > backupcentral.com>wrote:

Hello,

I have a question about nearline volumes.

We eject all our full tapes from library and also remove them from CAP. So
the tapes are not there physicaly. We have a script which is updating
locations, but first it finds out whether or not we have tape in a library
(via -q near). If the tape is in library, but the location differs, it
prints out an error message.

The problem is we are still getting these error messages, because when i
run
"mminfo -q near -xc, -r volume " I still have these volumes on the list
even if they are not physicaluy in the library... Our offsite storage guys
confirmed, that tapes arrived and are there. So its no way we can have them
in library.

Any ideas why is this? How is it possible? And how can I convince our
library to show only the tapes that are really there? how mminfo determines
whether the tape is in library or not?

+----------------------------------------------------------------------
|This was sent by lucia.ladonova < at > netkosice.sk via Backup Central.
|Forward SPAM to abuse < at > backupcentral.com.
+----------------------------------------------------------------------


"signoff networker" in the body of the email. Please write to
networker-request < at > listserv.temple.edu if you have any problems with this
list. You can access the archives at
http://listserv.temple.edu/archives/networker.html or
via RSS at http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER



via RSS at http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER

Post Near line volume? 
On 05 17, 2010, at 4:56 AM, kurtica wrote:

Hello,

I have a question about nearline volumes.

We eject all our full tapes from library and also remove them from CAP. So the tapes are not there physicaly. We have a script which is updating locations, but first it finds out whether or not we have tape in a library (via -q near). If the tape is in library, but the location differs, it prints out an error message.

The problem is we are still getting these error messages, because when i run
"mminfo -q near -xc, -r volume " I still have these volumes on the list even if they are not physicaluy in the library... Our offsite storage guys confirmed, that tapes arrived and are there. So its no way we can have them in library.

Any ideas why is this? How is it possible? And how can I convince our library to show only the tapes that are really there? how mminfo determines whether the tape is in library or not?

How do you eject your tapes from your tape library?


via RSS at http://listserv.temple.edu/cgi-bin/wa?RSS&L=NETWORKER

View user's profile Send private message
Post  
Aaron: I know, via sjirdtag, everything is OK. Tapes that are marked as nearline in mminfo are not visible via sjirdtag. But the problem still persists. We need to have mminfo updated, cause its the best way to update locations via script. On other libraries, we have no problem with it

we use nsrjb to withdraw tapes via script.

View user's profile Send private message
Display posts from previous:
Reply to topic Page 1 of 1
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
  


Magic SEO URL for phpBB